Search results

The belt height adjuster rattle is also real. I’ll tackle that next when I reassemble the interior. Glad to have helped!

Took my subframe off when doing my lower arm bushings upgrade. Should have just fixed this myself. If it can be done without dropping the subframe and redoing my alignment that’d be delightful.

Water Injection After much consideration I decided to use the AEM kit to just do water injection. I’ll tap into the washer reservoir instead of hooking up a tank in the rear. My intention is to mount the pump on the subframe front brace. Which is nothing more than a filmy sheet metal. I have...

RMM in today Heard good things about PRL RMM. If it ain’t sufficient I’d try the stiffer ones from Hasport. Battle Bee Oil Cooler oil cooler is quite a pain to install. Routing the piping is troublesome. Battlebee stuff is very well made imho. Shame that it isn’t widely available in NA yet...

Stripping the Engine Bay The bumper came off easily without needing to pry any clips as per some videos. drained the coolant and oil Out the plastic, in the sealed single piece tank! replaced the thermostat with a 68c one. Removed the mhi turbo and swapped it to 27Won Kuro (non plus). Heat...

Rattle Fix #2 - Headunit/Dashboard there’s some serious rattle around here. Gonna have to whip out the foam and felt tapes to tackle this. Update: I’ve eliminated the rattle 😎 Remove the four screws/bolts holding the Headunit. Undo the two connectors behind the Headunit and lift the Headunit...

Recaro Podiums Podiums arrived. I had in mind that I ordered red alcantara but received them in black. Probably have to order some red pads later on. I am well aware that these seats have driver and passenger shells where it’s determined by the FIA stickers location, I was still shipped with...

Was going through service manual looking for torque figures and I realized this: Did you really use new nuts and bolts every time you made adjustments / changed out parts?

Actually custom rims isn’t anything new but the forging process is not exactly the same as with say - Rays. The block is still compressed to over 10-12k tonne before being shaved to the shape you want. You can have it in any design and brake clearance you want. Those red lines are masking tape...

Yes sir

What was their ambient? Our climate here is like 36C 97F on a normal afternoon. Oil temp can go really high if not managed properly

No I decided on the OG kuro

I use Motul 300V 5W40 for hot and humid Asia weather here. 5W30 would break down to 20s easily and often times all the cars we have here that use 5W30 would see oil consumption. My 9y0 Cayenne would consume oil all the way from max to min within 12 months period. Those b58 engines with 5w30 oil...

Initially I wanted the rv6 660as but the chart just didn’t seem very right. Let me try this kuro and report back. I’m expecting some good low end results with the pracworks intake manifold in this build. Oh btw the only track I have here has a couple of long corners and a long straight. 400hp...

Reassembly Rattle Fix #1 I’m not sure what this module is but this is the cause of rattle under the dashboard around the hvac controller. It’s held by a push pin. You need to put your hand above and behind the controller and pinch it then lift up to remove it. Pad it with some foam tape before...

TSP Fender Rock Guard Installation Remove the screws. Pop the clips. I broke all of them. I’ve removed a lot of clips under the car and none broke but these clips are just especially fragile. Had some spare lying around so I used those. Gonna order some new original clips 🌚 Got myself some...

Stripping off the interior I’ve seen several videos where people use prying tools on the soft-touch dashboard and AC vent to remove them, risking scratches and damage. However, you can easily pop them out without any damage by first removing the side panel. Then, use your hand to push the AC...

Dashcam Installation I’ve been using DDPAI dashcams since their initial launch. They provide high-quality sensors and excellent post-processing. I prefer to install them myself, as many shops and technicians tend to rush the job, often skipping proper preparation and risking scratches. To...

This thread will detail down my FL5 build journey. Below are the list of parts acquired for the build. Cooling PWR Street Radiator Acuity Super Cooler Reverse Flow hose (Not compatible with PRL intake) PRL Intercooler PRL Charge pipe Battle Bee Oil Cooler w/92C thermostat Battle Bee...