What did you do to your FL5 today?

[Timszee]

Installed PRLs RMM at 1k miles. Install took 20 minutes. Really disappointed with Honda for putting the bolt in that direction.. NVH is almost non existent, motor stability is amazing when on and off throttle. Car feels more connected/solid. Also the quality of the mount is top tier. Anyone reading this on the fence about doing it.. Just do it..

Sponsored

 

[MERAKIAUTOWORKS]

Do you have the new remark tri tip in stock? I don't see it under products for the FL5.

Yes we do, feel free to message us.

-Josh

 

[AspecR]

Did my 4th and final oil change on the Honda ServicePass. Time to switch to 5W-30 for my next oil change. Installed the Hasport RMM, swapped out the spark plugs for NGK Rutheniums (part number: LKAR8BHX) and swapped the transmission fluid for RedLine MT-90(I highly recommend).

If everything goes according to plan, my Spoon springs, rigid collars and Garage Unique front lip will go on later this month(been sitting on them for over a year now).

 

[s2ktypeR]

Hey everyone, happy Friday! Yesterday, I ordered the OEM carbon fiber wing for my Type R and I'm super excited. I also got locking security screws for the FL5 Civic Type R rear spoiler. Is there anything else I should get? Any type of protection for this wing you might recommend? It looks like it will be easier to keep clean than the black OEM wing.

 

[L1SYC]

Hey everyone, happy Friday! Yesterday, I ordered the OEM carbon fiber wing for my Type R and I'm super excited. I also got locking security screws for the FL5 Civic Type R rear spoiler. Is there anything else I should get? Any type of protection for this wing you might recommend? It looks like it will be easier to keep clean than the black OEM wing.

Damn!!! That plate tho Good luck with the install

 

[Clark_Kent]

Hey everyone, happy Friday! Yesterday, I ordered the OEM carbon fiber wing for my Type R and I'm super excited. I also got locking security screws for the FL5 Civic Type R rear spoiler. Is there anything else I should get? Any type of protection for this wing you might recommend? It looks like it will be easier to keep clean than the black OEM wing.

I would plan to ceramic coat it, but nothing else. Side note - I had mine replaced under warranty for a failing clearcoat. Honda took care of it, no questions asked. Car looks fresh btw, I like the red license plate.

 

[Tickle]

Did my 4th and final oil change on the Honda ServicePass. Time to switch to 5W-30 for my next oil change. Installed the Hasport RMM, swapped out the spark plugs for NGK Rutheniums (part number: LKAR8BHX) and swapped the transmission fluid for RedLine MT-90(I highly recommend).

If everything goes according to plan, my Spoon springs, rigid collars and Garage Unique front lip will go on later this month(been sitting on them for over a year now).

How on earth did you get 4 out of it? I was able to get two!

Please @ me after the Spoon springs and collars are installed.

 

[AspecR]

How on earth did you get 4 out of it? I was able to get two!

Please @ me after the Spoon springs and collars are installed.

My service advisors love me I guess, did my oil changes every 5k miles with no issue. It's an easy survey for them to hit their bonus.

 

[s2ktypeR]

Damn!!! That plate tho Good luck with the install

Thank you, it should be an easy installation.

 

[s2ktypeR]

I would plan to ceramic coat it, but nothing else. Side note - I had mine replaced under warranty for a failing clearcoat. Honda took care of it, no questions asked. Car looks fresh btw, I like the red license plate.

I haven't tried a ceramic coating yet, but I think I might attempt applying it to the wing and the wheels. Thank you !!

 

[johnny.silva7]

+2HP with this reservoir sock

 

[BoostBlueFL5Rawr]

Finally made time to book an appointment to get my AWE exhaust, mud flaps, PRL hvi, charge pipes and intercooler installed. A bit disappointed in the intercooler as they had to cut the bumper support to make it fit but oh well. *** Update, spent the morning pulling the bumper to see what is up... intercooler was installed upside down, prl logo was to the passenger side... Had to remove the bumper support to get it off, flipped and all good now.***

 

[Tickle]

Finally made time to get my AWE exhaust, mud flaps, PRL hvi, charge pipes and intercooler installed. A bit disappointed in the intercooler as they had to cut the bumper support to make it fit but oh well.

View attachment 245569

Which intercooler?

 

[Icehawk]

I haven't tried a ceramic coating yet, but I think I might attempt applying it to the wing and the wheels. Thank you !!

If you do nothing else - coat the wheels! Game changer.

 

[johnny.silva7]

If you do nothing else - coat the wheels! Game changer.

Any recommendations on an easy-to-apply coating?

Sponsored