What did you do to your FL5 today?

[Geraldfl5]

wish you were closer to me in PA, I wanna hear this in person so bad since I'm torn between this and the AWE track. I want the louder option lol

I like the milltek with the valve louder then stock but not to crazy but with the valve open it get louder

Sponsored

 

[artsyfartsyFL5]

I like the milltek with the valve louder then stock but not to crazy but with the valve open it get louder

yeah I def want the most volume out of a Catback and from the videos I’ve seen, the milltek sounds louder and better than the awe track

 

[powerofdreams]

Minimal drone! I still have the stock front pipe and down pipe and it sounds similar to stock to be honest.

That's good. Maybe I'll pick up a front pipe if I get the HKS, might give it a bit more sound.

 

[SpoolinFK8]

Has anyone had any experience with the Pulstar Plasma Core Spark Plugs? Just received my set yesterday. Will be installing them soon.

 

[blueroadster]

Received shipment of the Fujitsubo exhaust and front pipe today. Here is the exhaust section:

I don't have a lift, so instead of using jack stands, there is enough clearance using ramps.

 

[Mobias]

Received shipment of the Fujitsubo exhaust and downpipe today. Here is the exhaust section:

I don't have a lift, so instead of using jack stands, there is enough clearance using ramps.

I've heard this is not much louder than stock on highway. I'd definitely like to hear thoughts!

 

[Toppyjai]

Received shipment of the Fujitsubo exhaust and downpipe today. Here is the exhaust section:

I don't have a lift, so instead of using jack stands, there is enough clearance using ramps.

 

[Toppyjai]

I found ASIMO I also had Spoon springs installed. Install was done at New Hope Auto in Brooklyn, NY.

 

[Mrjustin81]

Let there be A/C haha
Other than my not noticing the little tabs as I got fit really good otherwise. Not going to try to remove and get back in the same fit. Might try to trim those off.

 

[blueroadster]

I installed the Fujitsubo front pipe and exhaust this evening. I decided to just drive up onto two ramps in the front and used two jack stands in the back. Access was cramped without having enough space to use a creeper but overall, the install took about 2 hours to complete from start to finish. Everything lined up perfectly.

@Clark_Kent already shared detailed information and PICs of the Fujitsubo front pipe and exhaust in this post. Here is his follow up post with sound clips after installing while using the using the OEM downpipe.

My car has a TSP downpipe installed. Sound during a cold start has a deeper tone but around the same dB level.

 

[Yayo]

First tests

 

[Brittania]

First tests

Are those valve cover badges? If so please take my money!!!

 

[Yayo]

Are those valve cover badges? If so please take my money!!!

These are the numbered plates located on the dashboard, in front of the co-pilot.

 

[Brittania]

These are the numbered plates located on the dashboard, in front of the co-pilot.

Oh OK I thought they were badges to go on the valve cover. Would you be able to scale that design to a plate that is 90mm wide by 24mm high? Would be awesome!!

 

[Chilly613]

Oh OK I thought they were badges to go on the valve cover. Would you be able to scale that design to a plate that is 90mm wide by 24mm high? Would be awesome!!

This is what used to be on the intlet pipe on the FK8 and valve cover of other trims.

https://www.ebay.com/itm/255601183080

Two Step Performance is also making valve cover badges now.

https://www.twostepperformance.com/products/tsp-valve-cover-badges